OUR TECHNICAL STANDARDS

Caramella Quality:
Our Build Standards

Review the common stages and details that may appear in a Caramella cabinetry project. Site dimensions, materials, fittings and trade coordination are confirmed for each project.

Last updated:

QUICK ANSWER

Who this is for: homeowners, contractors, and architects who need a technical checklist for site readiness, fabrication standards, and installation coordination.

Use this page as the technical reference, then cross-check materials and hardware on the Build Standard page and submit project details via Contact Us.

"Materials, fittings and installation scope are recorded in the project quotation and approved drawings."

01. Site Readiness Standards

Confirm site dimensions and coordinate other trades against the approved drawings.

Use the approved production drawings to coordinate cabinet positions with the measured room, appliances, sockets, lighting and plumbing. Confirm final service locations with the relevant qualified trades before installation.

Flooring and walls: Review the installation sequence with the project team and confirm any finishing or site-preparation requirements for the specific project in writing.

Cabinet Dimensions and Proposal Scope

Cabinet dimensions are confirmed on the project drawings.

Cabinet dimensions and combinations vary by product and project. Compare the stated sizes and inclusions in each supplier's proposal.

Caramella cabinetry is fabricated to the approved project drawings using CNC machinery. The selected materials and fittings are recorded in the quotation.

COMPARE PROJECT DETAILS

  • Other proposal Check the specified products, dimensions, delivery and installation terms.
  • Caramella CNC-fabricated to the approved drawings; project scope and warranty are stated in the quotation.

"Final dimensions and clearances are reviewed on the approved production drawings."

A note on fillers and scribe panels: Their use depends on the measured wall, cabinet layout and selected finish. Review these details on the approved drawings.

How We Build Your Cabinets

Designs and fabrication are based on approved project drawings.

Project drawings are prepared and reviewed before fabrication.

Step 1: Design

Drafted in AutoCAD

Every panel, every joint, dimensions shown on the project drawings are reviewed before approval.

Step 2: Processing

Processed in Vectric Cut2D

The approved design is prepared for the fabrication workflow.

Step 3: Fabrication

Machined by Robot

CNC machinery processes cabinetry components according to the approved drawings.

Project coordination: Confirm fabrication, delivery, installation and any work by other trades in the project schedule.

02. The Manufacturing Timeline

Production lead time: typically 10-14 weeks from confirmation and customer sign-off of the production drawings.

Production lead time is typically 10–14 weeks from confirmation and customer sign-off of the production drawings. Confirm the project schedule with the team.

  1. Site measure and drawing sign-off
    The project dimensions and layout are recorded for review and customer sign-off.
  2. Material and hardware confirmation
    Selected materials, hardware and any stone details are recorded in the quotation and approved production drawings.
  3. Fabrication
    Cabinet components are prepared from the approved production drawings, including PUR edge sealing.
  4. Preparation for installation
    Confirm any inspection, delivery and site-access arrangements with the project team.
  5. Installation
    Installation work and countertop fitting are carried out according to the agreed project scope and schedule.

03. Cabinetry Terms (Glossary)

Common terms explained in plain English.

Defining the standard terminology used in our quotations and technical drawings.

Carcass
The carcass is the cabinet box behind the doors. Caramella's standard carcass material is ENF plywood unless another material is agreed for the project. Confirm the selected board in the quotation.
Gable End / End Panel
A gable end or end panel covers an exposed side of a cabinet run. Confirm the selected panel finish in the project specification.
Infill / Filler
An infill or filler closes a planned gap between cabinetry and a wall, appliance or other feature. Its size and finish are confirmed from the site measurement and approved drawings.
Waterfall Edge
A waterfall edge continues the countertop material down the side of an island or cabinet. Confirm feasibility, joints and finish for the selected quartz stone product in the quotation and drawings.
Kicker / Plinth
The panel covering the recessed space below base cabinets. Confirm the selected kitchen kickboard material and base detail in the quotation.
Pelmet
If you stick LED light strips under your upper cabinets, you don't want the harsh bulbs shining right in your eyes when you sit at the dining table. A pelmet is a small lip we add just below the cabinet line to hide the fixture while letting the light wash down the wall.

04. Recommended Materials for Each Room

Confirm selected materials, fittings and care details for each room.

Room use, measurements and selected products inform the cabinetry specification. Confirm materials, finishes, fittings and care instructions for the project.

The Wet Kitchen (Heavy Cooking)

For a kitchen, confirm the door finish from the available Formica and PET samples, the carcass material, hardware and installation scope. Caramella's standard carcass is ENF plywood unless another material is agreed, edge sealing uses PUR adhesive, and kitchen countertops are quartz stone. Follow the selected products' care instructions.

The Dry Kitchen (The Showpiece)

For a dry kitchen or island, compare the available finish samples and plan storage, appliance positions and circulation around the measured room. Quartz stone is the current kitchen countertop specification; check care and product details for the selected material.

Walk-In Wardrobes

For a wardrobe, plan shelves, hanging space, drawers and door clearance around the room and items to be stored. Confirm the selected boards, finishes, fittings and care requirements in the project specification.

05. How to Care for Your Cabinets

Tips to keep your joinery looking new.

Care tips to keep your cabinets looking their best.

Matte/Soft-Touch Surfaces
Cleaning guidance varies by product and finish. Follow the selected manufacturer's care instructions and check with the supplier before using a cleaner or abrasive product.
Engineered Quartz Stone
Follow the care instructions for the selected quartz stone product. Ask the supplier about cleaning, heat exposure and any limitations before use.
Hardware (Hinges & Runners)
Follow the hardware manufacturer's care guidance. Confirm the installed brand and model in the project specification.

Review Your Project Specification

Use the approved quotation and production drawings to confirm the products and details selected for your project.

PROJECT DETAIL

1. Edge-Banding Process

Genuine Caramella builds currently use PUR adhesive for edge banding.

PROJECT DETAIL

2. Carcass material

Caramella's standard carcass material is ENF plywood unless another material is agreed for the project. Confirm the chosen board and finish in the quotation and production drawings.

PROJECT DETAIL

3. Hardware Selection

Hardware is listed by brand and model in the approved project specification. Blum CLIP top is the primary hinge option, with DTC as an alternative. Optional HIGOLD storage accessories should be checked by selected model and cabinet fit against supplier documentation; do not infer a material specification from the brand name or a catalogue image.

Related Resources

Build Standard Guide

A one-page reference to Caramella's stated materials and process details. Compare these with the project-specific quotation and approved drawings.

View build standard →

Wet Kitchen Guide

Layout and specification questions for a kitchen project, including product and site details to confirm.

Wet kitchen guide →

Financing Options

BIBD At-Tamwil financing is available for Caramella projects. Customers apply and deal directly with Tamwil, which sets approval and financing terms.

Explore financing →

Legacy route: technical-specs/ — 301s here.